RWB Popsicles 16 Oz Wrap
UV DTF 16oz Wrap 9.4" x 4.2" Printed in house on our Commercial size printers 1-3 business day TAT
“U Press Transfers never disappoint.”
Shop app reviewWhy U Press UV DTF
- Printed in house on commercial UV DTF printers
- Sticks to glass, cups, wood, plastic, metal & more
- Bright colors with a glossy, raised finish
What you get
- One UV DTF cup wrap, 9.4" wide × 4.2" tall, sized for 16 oz cups.
- Only the wrap is included, not the cup in the photos.
- Printed in house on our commercial UV DTF printers.
- Made for hard surfaces. Not for fabric or clothing.
Shop all UV DTF cup wraps →Build your own UV DTF gang sheet → Upload a finished UV gang sheet file →
How to apply
- Clean the surface with rubbing alcohol and let it dry.
- Peel off the backing paper. The design stays on the clear film.
- Place it and rub it down from the center out, firmly, for 30–60 seconds with a squeegee or your fingers.
- Peel the clear film slowly at a low angle. If a part lifts, lay it back and rub again.
- Let it set for 24 hours before washing or heavy use.
Wrapping a cup? Line up the edge of the wrap with the seam on the side of the cup, keep it level and smooth it around the cup as you go.
No heat press needed. Apply at room temperature. More tips are further down this page.
Works on & care
Works on
- Glass cups, tumblers & mugs
- Ceramic & metal
- Wood, plastic & acrylic
- Phone cases, notebooks, signs & more
Care
- Wait 24 hours after applying before washing
- Hand wash for best results, with mild soap and warm water.
- Don't scrub with rough pads
- Need the dishwasher? Top rack only, on a low-heat setting, away from direct spray. Avoid the microwave.
Shipping & turnaround
- Printed fresh for every order, then packed and shipped.
- Ships within the Current TAT shown at the top of the site. TAT is business days to prepare, print and ship; transit time is added after it ships.
- Track your order any time to see which step it is on.
- Need it sooner? Add Rush Printing: printed same or next business day.
Apply it right
How to apply UV DTF
- No heat press
- Peel & stick
- Hard surfaces only
Apply 5 steps
- Clean the surface with rubbing alcohol and let it dry completely.
- Peel off the backing paper. The design stays on the clear top film.
- Place it and rub it down. Press from the center out, then rub firmly over the whole design for 30–60 seconds with a squeegee or your fingers.
- Peel the clear film slowly at a low angle. If any part lifts, lay the film back down and rub again.
- Let it set for 24 hours before washing or heavy use.
For best results
- Apply at room temperature, not on a hot or cold surface
- Firm pressure is the key: rub harder than you think
- Don't touch the sticky side of the design
- Smooth, flat or gently curved surfaces work best
- Store unused designs flat, away from heat and sunlight
- Wrapping a cup? Line up the edge of the wrap with the seam on the side of the cup, keep it level and smooth it around the cup as you go
UV DTF is made for hard surfaces. It is not for fabric or clothing.
Works on
- Glass cups, tumblers & mugs
- Ceramic & metal
- Wood, plastic & acrylic
- Phone cases, notebooks, signs & more
Not for fabric or clothing.
Care
A little care keeps your UV DTF looking new.
- Wait 24 hours after applying before washing
- Hand wash for best results, with mild soap and warm water.
- Don't scrub with rough pads
- Need the dishwasher? Top rack only, on a low-heat setting, away from direct spray. Avoid the microwave.
Shipping & turnaround
Printed fresh for every order, then packed and shipped.
- Ships within the Current TAT shown at the top of the site
- TAT is business days to prepare, print and shipTransit time is added after it ships
- Track your order any timeSee which step your order is on
- Need it sooner? Add Rush PrintingJumps to the front of the line, printed same or next business day
Pocket:
Toddler:
Youth:
Adult Small:
Adult Large:
Adult XL:






