Pressing instructions
Press it right, every time.
Time, temperature, pressure and peel for every U Press transfer. Start with these settings, then fine-tune for your heat press.
- 300°FHeat press temperature
- Heavy pressureFirm and even
- 8–12 secHot peel
- 12–15 secCold peel
DTF transfers
HiFi DTF, Legacy Prints and pre-made designs. Peel hot or cold, whichever you like.
How do I press with a hot peel?
- Heat your press to 300°F.
- Pre-press the shirt for 3–5 seconds to remove wrinkles and moisture.
- Place your transfer.
- Press with heavy pressure for 8–12 seconds.
- Peel the backing in one quick motion while it’s still hot.
- Press again for 5 seconds with parchment paper or a Teflon sheet.
How do I press with a cold peel?
- Heat your press to 300°F.
- Pre-press the shirt for 3–5 seconds to remove wrinkles and moisture.
- Place your transfer.
- Press with heavy pressure for 12–15 seconds.
- Let it cool completely, then peel the backing.
- Press again for 5 seconds with parchment paper or a Teflon sheet.
Hot peel or cold peel: which should I use?
Both work with our DTF transfers, so use whichever fits the way you work. Hot peel saves time because you peel right away. With cold peel you wait until the transfer has cooled.
Why do the second press?
The second press finishes the transfer. Different cover papers or fabrics give a different feel or finish, so try a few and see what you like best.
Do I cut a gang sheet apart before pressing?
Yes. Cut the designs apart and press each one on its own.
Glitter DTF
Glitter DTF is cold peel only.
How do I press Glitter DTF?
- Heat your press to 300°F.
- Pre-press the shirt for 3–5 seconds.
- Press with heavy pressure for 12–15 seconds.
- Let it cool completely, then peel the backing.
- Press again for 5 seconds with parchment paper or a Teflon sheet.
UV DTF
UV DTF is for hard surfaces. No heat press needed.
How do I apply UV DTF?
- Clean the surface with rubbing alcohol and let it dry.
- Peel off the backing paper.
- Place it and rub firmly over the whole design for 30–60 seconds with a squeegee or your fingers.
- Peel the clear film slowly at a low angle.
- Let it set 24 hours before washing.
Wrapping a cup? Line up the edge of the wrap with the seam on the side of the cup so it goes on straight, then smooth it around the cup as you go.
What can I put UV DTF on?
- Glass cups, tumblers and mugs
- Ceramic, metal, wood and plastic
- Phone cases, notebooks, signs and more
It isn’t made for fabric or clothing. Hand wash for best results. Need the dishwasher? Top rack only, on a low-heat setting, away from direct spray. Avoid the microwave.
Washing & care
How do I wash shirts with DTF transfers?
- Wait 24–48 hours before the first wash.
- Wash cold and inside out, with a soft detergent.
- Skip fabric softener and bleach.
- Air dry, or use the lowest dryer heat.
- Don’t iron directly on the print.
Tips & help
My transfer isn’t sticking. What should I check?
Not all heat presses are the same, so treat these settings as a starting point and adjust from there. Make sure you pre-pressed the shirt to remove moisture and used heavy pressure for the full time. Still not right? Call or email us and we’ll help.
Is there a pressing video?
Our pressing videos are coming soon. You’ll find them with our other video tutorials, next to the gang sheet and Mock Up Lab guides.
No answers match that. Try another word, or ask us below.
Still not sticking right?
Not all heat presses are the same. Call or email us and we’ll help you dial it in.


